Full tail kit as seen on the EMW eK100 Cafe Racer. Designed to match the lines and contours of funky K Bike tank shapes. Built in height and angle adjustment screws will ensure you nail your exact look.
eK100 Tail Kit Contains:
Main Tail - Solid ABS: finished and primed gray ready for paint or raw 3D print
Tail Base - Glass Filled ABS: finished primed black (can be installed as-is) ready for paint or raw 3D print
LED Strip Lights - One short (top) and one long (bottom) LED strip light
Dual Intensity Converter - Converts the the strip lights into separate brake and running signals
Retrorides Mount - Machined 6061 Aluminum left unfinished
Mounting Hardware - Hardware for mounting and alignment
Optional:
3 in 1 LED Lights - You can use all three functions: running, brake and turn signal; braking and turn signal, or just the turn signal only; you’re choice. Provides a great addition to your visibility when braking. You can add your own turn signals/lighting in the tapped M8 holes on the aluminum brackets if you choose the option without.
Not included: Retrosides subframe components or seat
Please note the purchase of this kit assumes acknowledgement of the following and cannot be returned due to this:
This is a 3D printed product, for the Paint Ready variant you will notice evidence of such on non-visible surfaces. All layer lines on visible surfaces will be eliminated and primed. The Raw 3D Print variant will require finishing (bondo, sanding, etc); this is the same starting condition we finish them from.
This kit is designed to mount to the Retrorides Subframe. The stock mounting tube length is 7in/177.8mm - you can enter a custom length when you add-to-cart if you need something different. You are responsible for providing this measurement, if not you will receive the stock length. The angle of the tail where it meets the back of the seat is DIFFERENT than the Retrorides Tail Design, you will have to adjust/bend your seat plate to get the right angle if you already have a seat - this was an aesthetic choice to match design lines.
For those that do not have the Retrorides Subframe but wish to adapt this kit into your setup, you can select the option to not include the aluminum frame for a price break. We provide no guarantee on fitment for non-Retrorides setups.
Reach out via the contact page for alternative options to adapt this kit to other setups.
Electric motorcycle NOT required, this is a lighting kit for any normal 12 volt system
Fully machined aluminum versions will be available in the near future, if interested please submit a request via the contact page, expect to be in the 500 - 700 USD range.
Full tail kit as seen on the EMW eK100 Cafe Racer. Designed to match the lines and contours of funky K Bike tank shapes. Built in height and angle adjustment screws will ensure you nail your exact look.
eK100 Tail Kit Contains:
Main Tail - Solid ABS: finished and primed gray ready for paint or raw 3D print
Tail Base - Glass Filled ABS: finished primed black (can be installed as-is) ready for paint or raw 3D print
LED Strip Lights - One short (top) and one long (bottom) LED strip light
Dual Intensity Converter - Converts the the strip lights into separate brake and running signals
Retrorides Mount - Machined 6061 Aluminum left unfinished
Mounting Hardware - Hardware for mounting and alignment
Optional:
3 in 1 LED Lights - You can use all three functions: running, brake and turn signal; braking and turn signal, or just the turn signal only; you’re choice. Provides a great addition to your visibility when braking. You can add your own turn signals/lighting in the tapped M8 holes on the aluminum brackets if you choose the option without.
Not included: Retrosides subframe components or seat
Please note the purchase of this kit assumes acknowledgement of the following and cannot be returned due to this:
This is a 3D printed product, for the Paint Ready variant you will notice evidence of such on non-visible surfaces. All layer lines on visible surfaces will be eliminated and primed. The Raw 3D Print variant will require finishing (bondo, sanding, etc); this is the same starting condition we finish them from.
This kit is designed to mount to the Retrorides Subframe. The stock mounting tube length is 7in/177.8mm - you can enter a custom length when you add-to-cart if you need something different. You are responsible for providing this measurement, if not you will receive the stock length. The angle of the tail where it meets the back of the seat is DIFFERENT than the Retrorides Tail Design, you will have to adjust/bend your seat plate to get the right angle if you already have a seat - this was an aesthetic choice to match design lines.
For those that do not have the Retrorides Subframe but wish to adapt this kit into your setup, you can select the option to not include the aluminum frame for a price break. We provide no guarantee on fitment for non-Retrorides setups.
Reach out via the contact page for alternative options to adapt this kit to other setups.
Electric motorcycle NOT required, this is a lighting kit for any normal 12 volt system
Fully machined aluminum versions will be available in the near future, if interested please submit a request via the contact page, expect to be in the 500 - 700 USD range.
Image 1 of 15
Image 2 of 15
Image 3 of 15
Image 4 of 15
Image 5 of 15
Image 6 of 15
Image 7 of 15
Image 8 of 15
Image 9 of 15
Image 10 of 15
Image 11 of 15
Image 12 of 15
Image 13 of 15
Image 14 of 15
Image 15 of 15